Products
- Waterjet Cutting Pumps-BEW-15
- Waterjet Cutting Pumps-BEW-22
- Waterjet Cutting Pumps-BEW-22F
- Waterjet Cutting Pumps-BEW-25
- Waterjet Cutting Pumps-BEW-22A
- Waterjet Cutting Pumps-BEW-22FS
- Waterjet Cutting Pumps-BEW-22B
- Waterjet Cutting Pumps-BEW-26
- Waterjet Cutting Pumps-BEW-26F
- Waterjet Cutting Pumps-BEW-22P
- Pneumatic Valves-PV1000
- Pneumatic Valves-PV2000
- Abrasive Cutting Heads-BEW-CH9000
- Abrasive Cutting Heads-BEW-CH7200
- Camcut Abrasive Cutting Machine
- 5 Axis Motion Controller
News
NCM Solution
Waterjet Cutting Pumps-BEW-22A

Description
As flagship system of BOHR-EDISON, BEW-22A is industrially proven in hundreds of installations world wide. Designed for continuous 24 hour, 7 days per week operation, the BEW-22A excels in cutting all materials in any application.
As flagship system of BOHR-EDISON, BEW-22A is industrially proven in hundreds of installations world wide. Designed for continuous 24 hour, 7 days per week operation, the BEW-22A excels in cutting all materials in any application.
Features & Advantages
Highly reliable proximity switches control the sequencing of the intensifier.
Oversized, low-load motor.
Low hydraulic oil pressure - 2,900 psi / 200 bars.
A dial, main compensator allows for simple control of the cutting water pressure.
A dual compensator provides lower, alternative, preset cutting pressures for tasks such as
piercing or drilling.
The unit has a hydraulic oil cooling system with a full-flow oil heat exchanger.
The oil reservoir has two access doors for easy maintenance.
Brass fittings are used on the entire inlet water system to protect against corrosion.
A complete set of spares, special tools, and comprehensive manuals are included with
each unit.
Highly reliable proximity switches control the sequencing of the intensifier.
Oversized, low-load motor.
Low hydraulic oil pressure - 2,900 psi / 200 bars.
A dial, main compensator allows for simple control of the cutting water pressure.
A dual compensator provides lower, alternative, preset cutting pressures for tasks such as
piercing or drilling.
The unit has a hydraulic oil cooling system with a full-flow oil heat exchanger.
The oil reservoir has two access doors for easy maintenance.
Brass fittings are used on the entire inlet water system to protect against corrosion.
A complete set of spares, special tools, and comprehensive manuals are included with
each unit.
Specifications
Design Pressure:
60,000 psi (4,140 bars)
Maximum Operating Pressure:
55,000 psi (3,800 bars)
High-Pressure Flow Rate:
1.00 gpm (3.78 lpm)
Intensifier Cycle Rate:
22 cycles/min. at max. flow rate
Electrical System:
Main Motor: 50 hp / 37 kW (TEFC)
208v / 3 ph. / 60 Hz
230v / 3 ph. / 60 Hz
460v / 3 ph. / 60 Hz
190v / 3 ph. / 50 Hz
380v / 3 ph. / 50 Hz
Air/Oil Heat Exchanger Motor:
1/4 hp / 0.18 kW
120 VAC / 1 ph. / 60-50 Hz
208 VAC / 1 ph. / 60-50 Hz
230 VAC / 1 ph. / 60-50 Hz
Motor Speeds:
1800 rpm @ 60 Hz
1500 rpm @ 50 Hz
Controls:
120 VAC / 24 VDC
Safety Shutdown Circuits:
High Oil Temperature
Low Oil Level
Low Water Pressure
Intensifier Over-speed
Intensifier Stall
Hydraulic System:
4.33 cu. in. (71 cu. cm) Axial Piston Pump
Max. Operating Pressure: 3,000 psi (207 bars)
Cooling Water Flow Rate: 2 gpm (7.56 lpm)
Low Pressure Cutting Water System:
Optimum Inlet Pressure: 65 psi (4.50 bars)
Booster Pump Setting: 225 psi (15.5 bars))
Orifice Capacity at 55,000 psi (3,800 bars):
Quantity / Orifice Diameter
1 - 0.014 in. (0.35 mm)
2 - 0.010 in. (0.25 mm)
4 - 0.007 in. (0.17 mm)
8 - 0.005 in. (0.12 mm)
Physical Dimensions:
Height: 44 inches (1.12 meters)
Width: 32 inches (0.80 meter)
Length: 80 inches (2 meters)
Weight: 2,000 pounds (910 kg)
Design Pressure:
60,000 psi (4,140 bars)
Maximum Operating Pressure:
55,000 psi (3,800 bars)
High-Pressure Flow Rate:
1.00 gpm (3.78 lpm)
Intensifier Cycle Rate:
22 cycles/min. at max. flow rate
Electrical System:
Main Motor: 50 hp / 37 kW (TEFC)
208v / 3 ph. / 60 Hz
230v / 3 ph. / 60 Hz
460v / 3 ph. / 60 Hz
190v / 3 ph. / 50 Hz
380v / 3 ph. / 50 Hz
Air/Oil Heat Exchanger Motor:
1/4 hp / 0.18 kW
120 VAC / 1 ph. / 60-50 Hz
208 VAC / 1 ph. / 60-50 Hz
230 VAC / 1 ph. / 60-50 Hz
Motor Speeds:
1800 rpm @ 60 Hz
1500 rpm @ 50 Hz
Controls:
120 VAC / 24 VDC
Safety Shutdown Circuits:
High Oil Temperature
Low Oil Level
Low Water Pressure
Intensifier Over-speed
Intensifier Stall
Hydraulic System:
4.33 cu. in. (71 cu. cm) Axial Piston Pump
Max. Operating Pressure: 3,000 psi (207 bars)
Cooling Water Flow Rate: 2 gpm (7.56 lpm)
Low Pressure Cutting Water System:
Optimum Inlet Pressure: 65 psi (4.50 bars)
Booster Pump Setting: 225 psi (15.5 bars))
Orifice Capacity at 55,000 psi (3,800 bars):
Quantity / Orifice Diameter
1 - 0.014 in. (0.35 mm)
2 - 0.010 in. (0.25 mm)
4 - 0.007 in. (0.17 mm)
8 - 0.005 in. (0.12 mm)
Physical Dimensions:
Height: 44 inches (1.12 meters)
Width: 32 inches (0.80 meter)
Length: 80 inches (2 meters)
Weight: 2,000 pounds (910 kg)
